Page 2 of 2

Re: ScooterHacking ReFlasher - ESC recovery/downgrade

Posted: Mon Jul 24, 2023 9:36 am
by venom125
Hello, is it possible to somehow flash DRV on ninebot d18?

Re: ScooterHacking ReFlasher - ESC recovery/downgrade

Posted: Mon Jul 24, 2023 6:03 pm
by venom125
I solved the problem myself, thanks for your attention!

Re: ScooterHacking ReFlasher - ESC recovery/downgrade

Posted: Wed Aug 09, 2023 5:32 pm
by Zw0k
Hello

i made this first time so i can not conekt to Target

I have made all right bud no conection

[ReFlasher] Starting..
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
Info : clock speed 450 kHz
Info : STLINK V2J34S7 (API v2) VID:PID 0483:3748
[ReFlasher] Found ST-Link
Info : Target voltage: 3.270400
Error: init mode failed (unable to connect to the target)
[ReFlasher] Couldn't connect to target

What can i do

i use the board from the pic

The LED´s blink grean and one red LED is on

i hope for help

Re: ScooterHacking ReFlasher - ESC recovery/downgrade

Posted: Wed Aug 09, 2023 6:37 pm
by Zw0k
I have use zadig-2.8 for the USB Connection

bud ther is one Mistake
Se Pic Below
Is this the reason ?

No WCID on USB

Re: ScooterHacking ReFlasher - ESC recovery/downgrade

Posted: Wed Aug 23, 2023 6:17 pm
by Bollshii
Hello

i made this first time so i can not conekt to Target

I have made all right bud no conection

[ReFlasher] Starting..
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
Info : clock speed 450 kHz
Info : STLINK V2J34S7 (API v2) VID:PID 0483:3748
[ReFlasher] Found ST-Link
Info : Target voltage: 3.270400
Error: init mode failed (unable to connect to the target)
[ReFlasher] Couldn't connect to target

What can i do

i use the board from the pic

The LED´s blink grean and one red LED is on

i hope for help

hey i had the same error.

STM32 ST-LINK Utility v4.6.0 is very likely what you are missing with this tool update the stick without having anything connected after that everything should work as described


Read the instructions that solved my problem.

https://rollerplausch.com/threads/st-li ... ring.4270/

Re: ScooterHacking ReFlasher - ESC recovery/downgrade

Posted: Sun May 26, 2024 10:21 am
by bulgaru
Hello!

Just wanted to give a small comment to the discussion. So it happened that I've encountered this thread when trying to flash the controller on my Ninebot Max G30LP. I've discovered an error in the flasher documentation. It appears that in the images provided as the guide to connecting the wires, the SWDIO and SWCLK are shown incorrectly.

As a more general comment - the controller for G30D and G30LP seem to be identical, minus one of the white connectors. The correct connection schema is provided here: https://rollerplausch.com/threads/st-li ... llen.4270/

Please update the flasher documentation (the image for G30D), since it can be quite confusing.
Also please add a separate image for the G30LP scooters.

Re: ScooterHacking ReFlasher - ESC recovery/downgrade

Posted: Wed May 29, 2024 3:14 pm
by itsrosey22
Warn : Cannot identify target as a STM32 family.

Does anybody know how to fix??

Re: ScooterHacking ReFlasher - ESC recovery/downgrade

Posted: Sun Jun 02, 2024 10:55 pm
by bulgaru
Warn : Cannot identify target as a STM32 family.

Does anybody know how to fix??
Can you share a photo of the controller and how you connected the ST-Link?